Due the auto diagnostic tool fault with the car or truck is half previous one particular will check out, and now the information stream is clearly the deviation is too massive, I feel around the Run in this kind of a time period of time after the fault code will nonetheless appear once more, it had been made a decision the issue very first the information inflow hand analysis, striving to locate the point of failure.
So as to confirm the accuracy on the data stream, specially repeatedly flame once again to start the engine, found every single startup information stream are to start with shut to -19%, and after that slowly climbed back to 18%, indicating that the issue does exist. Then triggered the failure what? Immediately after some discussion, the Injector seal terrible, leaks can cause the generation with the challenge. Evaluation of the idea is following the car ignition is turned off, given that the fuel injector is not sealed, the high-pressure fuel by means of the leakage in the injector in to the cylinder, the cylinder accumulation gasoline, to start the approach from the upcoming, the recently launched since the cylinder has been The fuel mixed normal gasoline also thick, the oxygen sensor might be detected as well thick signal back towards the J623, J623 will alter and lessen the quantity of fuel injection until revenue the adjustment value exceeds a certain worth Zaiwang Hui regulation. To confirm this, once the engine is running, disconnect the plug from the large stress fuel pump and fuel pump fuse till the engine shake and then immediately flip off gradually inside the gasoline line basically no gasoline. Plug and fuse plug it back in right after you turn off the key, and then promptly start off to observe the data stream, feeling right into a value lower than just some. Repeatedly attempted twice, chose to check out injector in exchange for that unique auto, the injector just altered totally new, but there isn't a promise that the new difficulty. But in exchange for your unique car or truck injector commences, the data movement has not improved, the injector can be excluded.
Under repair in difficulties, mixed with two Launch X431 GX3 fault codes and data flow, two oxygen sensors reflects a also lean, a reflection as well thick, the information stream to the adjustment worth too thick, and later on also thin, and significantly more than the normal selection . The ordinary understanding of both the engine handle unit J623 failure or J623 Bad Ground garbled seem Shiraai contradictory failure, but from now repair system to analyze line and J623 itself should really not have any difficulties. Then the question The place is it?
Is it Launch and X431 definitely the engine consumption method hasn't sealed the result of it? Through the difficulties code and data stream examination this is unlikely, but still the 1st test, start out the engine and enter the basic settings, input channel number 107, click Activate, the process commences to set, setting success display normal The program described to date will not seal the reason is usually excluded.
http://eobd21.xanga.com/771977427/the-vigilance-engine-temperature-is-caused-by-excessive-air-conditioning-work-abnormal/
Showing posts with label obd2 scan tool. Show all posts
Showing posts with label obd2 scan tool. Show all posts
Tuesday, 5 March 2013
Friday, 1 March 2013
The Tiguan motor emissions lights sometimes lit(I)
Tiguan 1.8T SUV car obd2 tools auto. The homeowners reported: car jogging for some time once the engine emissions lantern lit, this failure continues to be frequently fixed many times. Go through fault codes, the upkeep technician has replaced 4 injector, spark plugs, crankcase air flow valve. But after the test run once the fault continues to be not solved. Then ask for the writer technical help. Fault diagnosis: to acquire the suitable facts to know car maintenance, majoring technician informed the consultation of the auto, the car latest the child months has several repairs the fault, has replaced the front and rear oxygen sensor changed The gasoline pump assembly and gasoline filter replacement catalytic converters, but every time the customer automobile back again following a time period of your time to reproduce the condition. The maintenance technician to the injector and various relevant parts, highway check 1 00km procedure would not keep any fault codes. If you want to carefully ensure no matter if the failure has long been ruled out, the maintenance technician to just take an severe strategy to confirm no matter whether the failure to reproduce, that is, once the auto is stationary, accelerated to 3000r/min, for about 20min, this time the engine command unit again stored fault codes had been 08342 P2096 catalytic converter after the fuel adjustment procedure, cylinder column 1 also lean; 08598 P2196 Oxygen (02) sensor signal is "concentrated" cylinder column 1 sensor 1. Precisely the identical because the preliminary fault code.
Study fault codes show the way of the restore Launch X431 GX3 to routine maintenance function, the very first assessment of your meaning of the two fault codes P2096 catalytic converter after the gasoline adjustment process, cylinder column much too slender "for the failure is actually a three-way catalytic is behind the oxygen sensor G130, the rationale for your failure is summed up during the pursuing points:
1. The extra air without having taking under consideration an amount of money of air stream sensor in the cylinder combustion or catalytic converters preceding paragraph leak.
The gasoline offer is simply too smaller, these kinds of as very low oil pressure, gas injector fouling from the gas filter clogging.
3 poor oxygen Digiprog 3 sensor fault or oxygen sensor line.
4. The engine manage unit failure or terrible line.
http://obd2expresscouk.wordpress.com/2013/03/01/southeast-v3-ling-yue-is-difficult-to-start-overhaul/
Study fault codes show the way of the restore Launch X431 GX3 to routine maintenance function, the very first assessment of your meaning of the two fault codes P2096 catalytic converter after the gasoline adjustment process, cylinder column much too slender "for the failure is actually a three-way catalytic is behind the oxygen sensor G130, the rationale for your failure is summed up during the pursuing points:
1. The extra air without having taking under consideration an amount of money of air stream sensor in the cylinder combustion or catalytic converters preceding paragraph leak.
The gasoline offer is simply too smaller, these kinds of as very low oil pressure, gas injector fouling from the gas filter clogging.
3 poor oxygen Digiprog 3 sensor fault or oxygen sensor line.
4. The engine manage unit failure or terrible line.
http://obd2expresscouk.wordpress.com/2013/03/01/southeast-v3-ling-yue-is-difficult-to-start-overhaul/
Tuesday, 26 February 2013
Honda Accord power steering method fault detection analysis
Honda Accord car ECU programmer sedan together with the continual flow hydraulic power steering technique, the method primarily consists of power steering, the steering mechanism and steering linkage components. The energy of steering device which includes power steering, power steering pumps, storage tanks, oil hoses and piping. Steering mechanism consists of a steering wheel (which includes the driver's seat airbag assembly) as well as the steering shaft. Steering
Guangzhou Honda Accord sedan using the continuous flow hydraulic power steering system, the technique mostly consists of energy steering, the steering mechanism and steering linkage parts. Energy steering device incorporates energy steering, power steering pumps, storage tanks, oil hoses and piping etc.. Steering mechanism includes a steering wheel (like the driver's seat airbag assembly) as well as the steering shaft. Steering linkage pitman arm, steering rod, shock absorbers and steering knuckle arm. The steering gear rack and pinion energy steering, steering pump rotor type.
Basic failure vas 5054a in the failure on the power steering program, steering noise and oil leakage. The basic failures contain tough steering, steering shocks, steering not functioning and steering kickback. A few of these faults may possibly be connected to energy steering, steering controls and steering linkage are associated. Brought on by the failure from the following describes the power steering device adverse, please refer for the basic failure with the vehicle steering mechanism with steering failure caused by the transmission mechanism analysis.
Initially, the general failure
(A) difficult steering
1. Failure phenomenon: Driving turn, turn the steering wheel really feel heavy effortlessly. Checking the rotational force with the steering wheel, and its value is greater than 30N.
2. Failure Evaluation
(1) Verify the oil tank is in oil, power steering pump drive belt is slipping, must confirm that no air within the program.
(2) Verify fgtech, fgtech galletto 2-master the energy steering pump pressure. Measuring the idle static hydraulic pressure manage valve and shut-off valve is totally open, the oil stress value ought to be equal to or slightly much less than 1500 kPa, otherwise it should be checked into the oil amongst the power steering and energy steering pump and return line The hose is clogged, aging or deformation. When the tubing is regular, then the steering gear rotary valve failure.
(3) when the measured energy steering pump stress is standard, within the case of your pressure manage valve and also the shutoff valve is totally closed, the measurement when idling pump unloading pressure, and its worth should be 7200 ~ 7800kPa. Unloading pressure is also low, you'll want to verify the flow manage valve and oil pump assembly.
(4) When the above checks unloading stress is typical, verify the rotation of the steering wheel towards the left and to the appropriate in the turning force, the difference in between the two need to be
http://www.youtube.com/watch?v=WncOHdAsxuQ
http://obd2express.overblog.com/diagnosis-of-faults-with-wang-asked
Guangzhou Honda Accord sedan using the continuous flow hydraulic power steering system, the technique mostly consists of energy steering, the steering mechanism and steering linkage parts. Energy steering device incorporates energy steering, power steering pumps, storage tanks, oil hoses and piping etc.. Steering mechanism includes a steering wheel (like the driver's seat airbag assembly) as well as the steering shaft. Steering linkage pitman arm, steering rod, shock absorbers and steering knuckle arm. The steering gear rack and pinion energy steering, steering pump rotor type.
Basic failure vas 5054a in the failure on the power steering program, steering noise and oil leakage. The basic failures contain tough steering, steering shocks, steering not functioning and steering kickback. A few of these faults may possibly be connected to energy steering, steering controls and steering linkage are associated. Brought on by the failure from the following describes the power steering device adverse, please refer for the basic failure with the vehicle steering mechanism with steering failure caused by the transmission mechanism analysis.
Initially, the general failure
(A) difficult steering
1. Failure phenomenon: Driving turn, turn the steering wheel really feel heavy effortlessly. Checking the rotational force with the steering wheel, and its value is greater than 30N.
2. Failure Evaluation
(1) Verify the oil tank is in oil, power steering pump drive belt is slipping, must confirm that no air within the program.
(2) Verify fgtech, fgtech galletto 2-master the energy steering pump pressure. Measuring the idle static hydraulic pressure manage valve and shut-off valve is totally open, the oil stress value ought to be equal to or slightly much less than 1500 kPa, otherwise it should be checked into the oil amongst the power steering and energy steering pump and return line The hose is clogged, aging or deformation. When the tubing is regular, then the steering gear rotary valve failure.
(3) when the measured energy steering pump stress is standard, within the case of your pressure manage valve and also the shutoff valve is totally closed, the measurement when idling pump unloading pressure, and its worth should be 7200 ~ 7800kPa. Unloading pressure is also low, you'll want to verify the flow manage valve and oil pump assembly.
(4) When the above checks unloading stress is typical, verify the rotation of the steering wheel towards the left and to the appropriate in the turning force, the difference in between the two need to be
http://www.youtube.com/watch?v=WncOHdAsxuQ
http://obd2express.overblog.com/diagnosis-of-faults-with-wang-asked
Sunday, 24 February 2013
Engine won't start and the way to complete?
We really should first auto diagnostic tool check out whether the distributor, spark plugs, electrical power lines, and so on. since the vehicle rain and also other moisture. In case the damp parts to dry, and after that launched. Directly or make use of the hair dryer blowing wet parts.
Second, check the spark plug for injury. If damaged, exchange the spark plug is usually so long as. Usually, automotive spark plug mileage of about twenty,000 to thirty,000 kilometers.
Test the battery voltage is adequate. The numerous batteries designed to the detection of the observation hole green when normal use, a black, must add factors, or maintenance, a white battery replaced.
Parking fail to remember to turn off the lights, it's possible you'll run from electrical power. If so, twist the ignition switch while in the ON position, the vehicle is linked for the second gear, foot clutch drag auto when traveling to a particular velocity, release the clutch, the car or truck are going to be capable to naturally start out. This strategy applies to only the electrical power failure, if your ignition program challenges, this technique not simply isn't going to function, may perhaps also possess a lousy result on catalytic converters, the auto also will harm the timing belt, result in major mechanical failure. Installing automated transmission car or truck, can't the carts get started, readily available jumper cables to connect the battery to start the engine with the other auto.
Edit this paragraph 5 maintenance underhand
1, oil plus sugar
Sugar entering the engine can be heated into fgtech a paste which can lead to the engine to 'hold tile', will not be functioning properly. The owners observed wrong car once more returned for fix, the owner can seize the opportunity with enthusiasm Henzai a.
2, gearbox oil plus brine
Gearbox oil brine into Riga, the gearbox will produce paste piece gearbox dress in, can accelerate the auto in about half the time, ranging from back to exchange the gearbox chip, substitute gearbox.
3, Brake oil plus alcohol
Brake fluid against alcohol, you are able to pace up the brake method dress in, "buddy" to open automotive plant owners will return following a few days there to exchange the entire brake components.
4, antifreeze salt vas 5054a
The extra salt antifreeze in to the engine tank, not only will develop scale tank, the circulating water flow, but also significant corrosion tank, triggering the tank harm. The owners head to replace the tank, "buddy" will warm reception.
5, the cleaning solution was extra caustic soda
Engine cleaning fluid to the Riga caustic soda, will accelerate the aging on the plastic pad, will induce a series of complications, "buddy" tea back to you "a good soak, seasoned servicing workers to find out the owners back time even the bad cannot 1 day
http://blogs.rediff.com/obd2expresscouk/2013/02/25/diagnostic-trouble-using-the-touch-method/
Second, check the spark plug for injury. If damaged, exchange the spark plug is usually so long as. Usually, automotive spark plug mileage of about twenty,000 to thirty,000 kilometers.
Test the battery voltage is adequate. The numerous batteries designed to the detection of the observation hole green when normal use, a black, must add factors, or maintenance, a white battery replaced.
Parking fail to remember to turn off the lights, it's possible you'll run from electrical power. If so, twist the ignition switch while in the ON position, the vehicle is linked for the second gear, foot clutch drag auto when traveling to a particular velocity, release the clutch, the car or truck are going to be capable to naturally start out. This strategy applies to only the electrical power failure, if your ignition program challenges, this technique not simply isn't going to function, may perhaps also possess a lousy result on catalytic converters, the auto also will harm the timing belt, result in major mechanical failure. Installing automated transmission car or truck, can't the carts get started, readily available jumper cables to connect the battery to start the engine with the other auto.
Edit this paragraph 5 maintenance underhand
1, oil plus sugar
Sugar entering the engine can be heated into fgtech a paste which can lead to the engine to 'hold tile', will not be functioning properly. The owners observed wrong car once more returned for fix, the owner can seize the opportunity with enthusiasm Henzai a.
2, gearbox oil plus brine
Gearbox oil brine into Riga, the gearbox will produce paste piece gearbox dress in, can accelerate the auto in about half the time, ranging from back to exchange the gearbox chip, substitute gearbox.
3, Brake oil plus alcohol
Brake fluid against alcohol, you are able to pace up the brake method dress in, "buddy" to open automotive plant owners will return following a few days there to exchange the entire brake components.
4, antifreeze salt vas 5054a
The extra salt antifreeze in to the engine tank, not only will develop scale tank, the circulating water flow, but also significant corrosion tank, triggering the tank harm. The owners head to replace the tank, "buddy" will warm reception.
5, the cleaning solution was extra caustic soda
Engine cleaning fluid to the Riga caustic soda, will accelerate the aging on the plastic pad, will induce a series of complications, "buddy" tea back to you "a good soak, seasoned servicing workers to find out the owners back time even the bad cannot 1 day
http://blogs.rediff.com/obd2expresscouk/2013/02/25/diagnostic-trouble-using-the-touch-method/
Thursday, 21 February 2013
Diagnostic fault observation
The so-called obd2 code reader observation is the auto mechanic carefully observed the car users pointed out the location of fault fault phenomena, and then judge the fault, which is an application up to the most basic and most effective method of fault diagnosis. Such as hair dryer exhaust pipe to take the blue smoke of failure, to judge the phenomenon can take the blue smoke, such as in the course of long-term risk Lanyan really long mileage engines use generally can be judged as a cylinder or piston ring wear , resulting with the gap is too large obd2 scan tool, due to the oil pan of oil fleeing into the combustion chamber through the clearance between the piston ring and cylinder wall; future risk Lanyan if only emits blue smoke when the engine just a launch gradually become more mild and generally can be to judge the rod block oil engine valve cover aging or bore wear to block oil disabled, but a small amount of oil leaking into the cylinder along the valve stem caused obd2 scanner.
The experience can accurately judge, the inexperienced should further observation. In the observation process, but also with the experience and theory, make careful thinking and push the card can not be simply sloppy, can not be fooled by appearances. Some phenomenon for those with experience is not suddenly be able to see clearly, then they would have to look at a few times, careful observation, to the outside to the inside, to see through obd2 bluetooth the fault phenomenon.
The experience can accurately judge, the inexperienced should further observation. In the observation process, but also with the experience and theory, make careful thinking and push the card can not be simply sloppy, can not be fooled by appearances. Some phenomenon for those with experience is not suddenly be able to see clearly, then they would have to look at a few times, careful observation, to the outside to the inside, to see through obd2 bluetooth the fault phenomenon.
Subscribe to:
Posts (Atom)